Whip Mix Pro 200 Bedienungsanleitung

Pro 200 Series FurnaceOperators ManualPro Press 200Pro 200Whip Mix Corporation • 361 Farmington Ave. • P.O. Box 17183 • Louisville, KY 40217-0183 USA5

10Pro 200 Series Furnace Operations Manual Using the Furnace After the furnace has completed the self-test at power up, the Firmware Version appears o

11Pro 200 Series Furnace Operations Manual Chapter Two — Special FunctionsMost Special Functions can be performed while a program is running, however

12Pro 200 Series Furnace Operations Manual Set Vacuum LevelThe factory setting for vacuum is 71 cm of mercury. The acceptable range is from 22 cm to 7

13Pro 200 Series Furnace Operations Manual Set Program Start DelayThe furnace has a unique feature that allows the operator to program a delay to occu

14Pro 200 Series Furnace Operations Manual Saving Programs to a Flash Drive (Exporting)1. Place the Flash Drive in the USB slot on the left side of th

15Pro 200 Series Furnace Operations Manual Low Fusing AdjustCalibration (800° C/1470° F or below)1. Select the Special Functions item from the Main Me

16Pro 200 Series Furnace Operations Manual Testing Your FurnaceThe Pro Series Furnaces are capable of performing several tests to aid in diagnosing th

17Pro 200 Series Furnace Operations Manual Chapter Three — Change Program MenuLook at a ProgramThe Look at a Program feature allows the operator to vi

18Pro 200 Series Furnace Operations Manual Add/Edit a ProgramAdd/Edit a Program is used to enter a new program or Edit a pre-existing program. This se

19Pro 200 Series Furnace Operations Manual 11. Hold Temperature Hold Temperature or the top temperature is the final, highest temperature in a 1-Stag

2Pro 200 Series Furnace Operations Manual The Pro Series Furnace comes complete with:WarrantyUnited States and CanadaWhip Mix Corporation warrants the

20Pro 200 Series Furnace Operations Manual Press Firing Cycle Program (Pro Press 200 only)The following procedures describe how to enter a pressing pr

21Pro 200 Series Furnace Operations Manual 8. Entry Temperature Entry Temperature is the temperature at which the table will close completely. The r

22Pro 200 Series Furnace Operations Manual Copy/Change a ProgramThe Copy/Change a program feature allows a program to be copied from one program numbe

23Pro 200 Series Furnace Operations Manual Turn the Selector Knob until the desired program is displayed. If the table has not been lowered, do so now

24Pro 200 Series Furnace Operations Manual The LED GraphThe LED graph follows the running Program’s progress and provides a quick visual reference on

25Pro 200 Series Furnace Operations Manual Running a Pressing Program(Pro Press 200 only)The Pro Press 200 can press into a 100, 200, or 300 gram inve

26Pro 200 Series Furnace Operations Manual Cleaning The FurnaceYour new furnace may be cleaned by using a soft cloth and kitchen cleaners such as Fant

27Pro 200 Series Furnace Operations Manual Trouble Shooting GuideThe Pro 200 and Pro Press 200 furnaces offer a number of self checks and warning mess

28Pro 200 Series Furnace Operations Manual FusesThe furnace contains two fuses:• On the rear, just below and to the right of the power cord, there ar

29Pro 200 Series Furnace Operations Manual Replacement PartsPart Number Description96004 Power Cord 115V96008 Power Cord 230V96001 Ceramic Plunger Rod

3Pro 200 Series Furnace Operations Manual Table of ContentsChapter Three — Change Program MenuLook at a Program ...

30Pro 200 Series Furnace Operations Manual High-Efficiency Vacuum PumpPro Check AdaptorProCheck Calibration Check DevicePro Cal Pro Series Accessories1

31Pro 200 Series Furnace Operations Manual Fahrenheit to Centigrade ° F ° C ° F ° C ° F ° C ° F ° C 100 38 630 332 1,160 627 1,690 921

IT 11522 05/1015946 Pro Series 200 Manual_ENG.indd 32 5/4/10 11:47 AM

4Pro 200 Series Furnace Operations Manual External Component LocatorSelector KnobVacuum Pump Hose BarbPower SwitchPower Inlet PlugFusesArgon Hose Barb

5Pro 200 Series Furnace Operations Manual Chapter One — Getting StartedYou are undoubtedly eager to unpack, set up, and begin using your new furnace.

6Pro 200 Series Furnace Operations Manual Quick-Cool Jet Installation for Pro 200 Furnaces with Air Cool JetPreparation:1. Remove the vacuum pump from

7Pro 200 Series Furnace Operations Manual Power• The furnace requires 115 Vac and 12 Amps of current in the United States and 220–240 Vac and 6.3 Amp

8Pro 200 Series Furnace Operations Manual Menu Selection ButtonsThe three menu selection items (Run Program, Change Program and Special Functions) wil

9Pro 200 Series Furnace Operations Manual Information Display and EntryDISPLAY — All information and user prompts will be shown on the display (four l